先准备软件包，然后解压缩，

# unzip rsc2.2.3_packages_s8.zip

解压缩后出现很多的软件包，如下：

README SUNWfrscd SUNWkrscd

README-RSC SUNWfrscj SUNWkrscj

SUNWcrsc SUNWhrsc SUNWrsc

SUNWcrscd SUNWhrscd SUNWrscd

SUNWcrscj SUNWhrscj SUNWrscj

SUNWdersc SUNWirscd SUNWsrscd

SUNWdrscd SUNWirscj SUNWsrscj

SUNWdrscj SUNWitrsc SUNWsvrsc

SUNWerscd SUNWjersc en_us_relnotes.pdf

SUNWerscj SUNWjrscd rsc2.2.3_packages_s8.zip

SUNWesrsc SUNWjrscj rsc2.2.3_packages_s9.zip

SUNWfrrsc SUNWkrsc软件包中是针对不同语言环境不同的软件包，英文的软件包是必须安装的，中文的软件包是
SUNWcrsc SUNWcrscd SUNWcrscj

英文的软件包是：
SUNWrsc SUNWrscd SUNWrscj

除了中文和英文的软件包外把多余的软件包删除掉，剩下如下软件包：

README SUNWcrscj en_us_relnotes.pdf

README-RSC SUNWrsc rsc2.2.3_packages_s8.zip

SUNWcrsc SUNWrscd rsc2.2.3_packages_s9.zip

SUNWcrscd SUNWrscj

然后安装这些软件包。

# pkgadd -d .

安装完之后，会在/usr/platform/`uname -i`/ 路径下生成rsc目录

# cd /usr/platform/`uname -i`/rsc

# ./ rsc-initscript

# ./rsc-config

Continue with RSC setup (y|n): y

Set RSC date/time now (y|n|?) [y]:
Server Hostname [SUN280R]:
Edit customer info field (y|n|?) [n]:
Enable RSC Ethernet Interface (y|n|s|?) [n]: y
RSC IP Mode (config|dhcp|?) [dhcp]: n
RSC IP Mode (config|dhcp|?) [dhcp]: config
RSC IP Address []: 192.168.81.12
RSC IP Netmask [255.255.255.0]:
RSC IP Gateway []: 192.168.81.254
Enable RSC Alerts (y|n|s|?) [n]:
Enable RSC Modem Interface (y|n|s|?) [n]:
Enable RSC Serial Port Interface (y|n|s|?) [n]:
Setup RSC User Account (y|n|?) [y]:
Username []: admin
User Permissions (c,u,a,r|none|?) [cuar]:



--------------------
Verifying Selections
--------------------


General Setup
-------------
Set RSC date now = y
Server Hostname = PMDB01

Set Customer Info = n

Is this correct (y|n): y



Ethernet Setup
--------------
IP Mode = config
IP Address = 192.168.81.12
IP Netmask = 255.255.255.0
IP Gateway = 192.168.81.254

Is this correct (y|n): y



Alert Setup
-----------
- Alerts disabled

Is this correct (y|n): y



Modem Setup
-----------
- Modem disabled, ppp disabled

Is this correct (y|n): y



Serial Port Setup
-----------------
- Serial port disabled

Is this correct (y|n): y



User Setup
----------
User Name = neusoft
User Permissions = cuar

Is this correct (y|n): y


This script will now update RSC, continue? (y|n): y
Updating flash, this takes a few minutes
........................................
........................................
........................................
........................................
........................................
........................................
........................................
...........................
Download completed successfully

Resetting RSC (takes about 90 seconds):
DONE
Setting up server to update RSC date on boot: DONE
Setting up server hostname: DONE
Setting up ethernet interface: DONE
Disabling RSC alert engine: DONE
Disabling modem interface: DONE
Disabling serial port interface: DONE
Adding user to RSC:
rscadm: user already exists
when this script completes,
use the rscadm command to correct the error.
Resetting RSC (takes about 90 seconds):
Are you sure you want to reboot RSC (y/n)? y


DONE
Setting up RSC date: DONE

*******************************
RSC has been successfully setup
*******************************

至此，配置完毕，可以使用telnet连接RSC了

与V240类似，系统也提供了rscadm命令用于在正常状态下管理配置rsc!不再赘述。